HVAC & Plumbing in Maryland Heights, MO

Installed a new 40-gallon tall gas tank-type water heater, connecting the cold and hot water lines, gas supply with control valve, and flue venting to the existing overhead ductwork. Verified proper connections and system operation, with the unit set up for delivery and the work meeting jurisdictional requirements.

Replaced the failed draft inducer motor on the gas furnace with a new unit, reinstalling the mounting gasket and securing the assembly to the blower housing. Verified wiring connections and flue connection were intact, and confirmed proper inducer operation and furnace startup sequence upon completion. The removed motor was discarded.

Responded to a no-heat call for a burning odor from a Lennox furnace installed in a crawlspace. Inspected the furnace control cabinet and integrated control board, including terminal block connections and low-voltage wiring harness, and found no evidence of burn marks, corrosion, overheating, or damaged conductors. System was found shut off by the homeowner; the cause of the odor was not conclusively identified from visual inspection of the control board and wiring.

Performed an on-site assessment for a standby generator installation, including inspection of the natural gas service and meter assembly to evaluate fuel supply capacity and connection routing. Surveyed the basement to determine the electrical panel route, conduit and cable pathways, and potential transfer switch placement, noting exposed joists, existing cabling, and PVC piping to be coordinated around during installation.

Performed a heating tune-up on one gas furnace, including removal of access panels and inspection of the burner compartment, control board, gas valve assembly, and wiring harness. Serviced the flame sensor/igniter assembly and removed the dirty, dust-loaded pleated air filter for replacement to restore proper airflow and combustion performance. Verified system components were in good condition and the unit was reassembled and ready for operation.

Performed a tune-up on one gas furnace, including removal of the front access panel and visual inspection of the burner compartment, flue pipe, wiring harness, and electrical components. Verified thermostat operation and noted moisture on the flue pipe and cabinet exterior along with dampness on the surrounding floor, indicating possible condensation or a leak that should be evaluated further.

Installed a new 40-gallon tall natural gas State ProLine water heater, connecting new copper supply piping with soldered fittings, a 3/4" temperature and pressure relief valve, and a shutoff valve. Mounted an expansion tank to the supply line, reconnected the gas line, and routed the galvanized flue to the existing vent system. Verified the installation is clean and leak-free with no visible corrosion.

Responded to a no-heat call on an approximately 4-year-old Goodman furnace and inspected the cabinet, pressure switch, and related wiring and hose connections. Used a dual-port manometer to measure pressure at the pressure switch circuit, recording a negative pressure reading of -1.31 in. w.c., to evaluate draft inducer operation and verify proper switch function.

Accessed the 4" exterior cleanout, removed the cap, and hydro-jetted the main sewer line to clear obstructions and restore proper flow. Inspected the corroded cast iron cleanout opening, which showed heavy rust and scaling along the interior walls, and replaced the cap upon completion.

Performed a routine heating tune-up on a furnace approximately 10 years old, inspecting the system and verifying operation, with no specific problems or symptoms reported. Used a clamp meter to measure electrical current draw (approximately 5.24 A AC) to confirm components were operating within normal range, and noted service labeling and ductwork in satisfactory condition with no heavy rust or corrosion observed.

Performed a heating tune-up on one 1-year-old gas furnace, removing the upper access panel to inspect the control wiring, blower and inducer motor assembly, and electrical connections, and verifying the PVC intake/exhaust piping and coupling were secure. Confirmed the furnace operated properly through the heating cycle with the thermostat responding to calls for heat, and checked the gas piping connections and adjacent AprilAire unit for normal condition. Reinstalled all panels and left the system running properly.

Returned to complete the scheduled light fixture installation. Removed the existing fixture, verified power was off, and installed the new flush-mount dome fixture with a frosted glass shade, securing it to the ceiling box and making the wire connections. Restored power and confirmed the fixture operates properly.

Responded to a bedroom outlet and switch malfunction by inspecting the residential electrical system, including the main breaker panel and associated branch circuits. Opened and evaluated the panel, noting dense, disorganized conductor routing, mixed-brand breakers (Bryant, Eaton, Square D), tandem breakers, and dirt and corrosion-related discoloration, and verified circuit labeling for the bedroom circuit. Documented panel conditions with photos and recommended further evaluation of the panel's condition and wiring.

Performed a seasonal heating tune-up on one gas-fired furnace with attached air handler. Inspected the cabinet, PVC vent and condensate piping, electrical conduit, and junction box, finding no visible rust, frost, or damage. Verified the programmable thermostat operates properly, with the display and set point (75°F) responding normally, and confirmed the system is ready for heating season.

Responded to a clogged double-basin kitchen sink and inspected the under-sink PVC drain assembly, including the slip-nut joints and P-trap, for restrictions. Cleared the blockage from the drain line, restoring free flow, and verified proper drainage from both basins with sustained running water and no leaks at the trap connections.

Replaced hardwired smoke alarms with customer-supplied units, securing each to its mounting base and labeling the installation date on the unit. Inspected and addressed the non-functioning wall switches at the double-gang switch plate, verifying proper operation and a secure, intact cover plate.

Completed scheduled heating maintenance tune-up on 16-year-old furnace unit. Performed comprehensive system inspection including blower motor, gas valve assembly, electrical connections, and all internal components. Verified proper operation of all controls, tested system with diagnostic equipment, confirmed all safety mechanisms functioning correctly, and documented system specifications. Unit operating within normal parameters with no issues identified.

Completed comprehensive tune-up and maintenance on a 12-year-old furnace system located in the basement. Performed standard maintenance protocol including inspection of all major components, burner assembly, heat exchanger, blower motor, and electrical connections. Inspected Honeywell motor assembly and associated wiring harnesses with multiple electrical connections confirmed secure. Identified significant condensation issues on metal ductwork with heavy frost and ice buildup on exterior surfaces, along with visible rust and corrosion on galvanized ducting indicating ongoing moisture infiltration and inadequate insulation. Documented deteriorated duct condition with oxidation present on multiple sections of vertical supply plenum. Recommended immediate attention to ductwork insulation and moisture control to prevent further corrosion and improve system efficiency. System operational at time of departure with all safety controls functioning properly.

Conducted comprehensive electrical assessment for converting two-prong ungrounded outlets to three-prong grounded receptacles throughout the residence. Inspected main electrical panel to verify grounding system integrity, evaluated existing circuit breaker configuration, and assessed bus bar connections and grounding conductor pathways. Documented current electrical infrastructure including surface-mounted conduit runs and existing receptacle locations to determine scope of work required for proper grounding installation and code compliance upgrades.

Completed heating tune-up on basement furnace unit, including full system inspection, filter replacement with new 20x24x1 pleated filter, and verification of all safety controls and operational parameters. System tested and confirmed operating within manufacturer specifications with proper airflow and combustion efficiency.