Kirkwood HVAC & Plumbing Services

Responded to scheduled service call for HVAC system. Upon arrival, documented existing conditions including condensate drainage system with PVC piping and union fitting, drip pan with standing water accumulation, and evidence of moisture intrusion along foundation perimeter showing black mold growth on subflooring and metal trim junction. Job was cancelled after dispatch and equipment arrival, with photographic documentation completed prior to departure.

Completed comprehensive cooling system tune-up on single residential unit located in side yard. System is under 10 years old and in good operating condition. Performed standard maintenance protocol including inspection of all major components, verified refrigerant levels, checked electrical connections, cleaned condenser coils, and tested system operation. Inspected and documented air filter condition within air handler unit - filter appears clean with minimal debris accumulation. All ductwork connections secure with no visible leaks or damage observed. System operating within normal parameters with no deficiencies noted at time of service.

Completed comprehensive cooling maintenance on a 9-year-old air conditioning system. Performed standard tune-up procedures including inspection of control board and electrical connections, verification of proper wiring and component operation, and filter assessment. System tested and confirmed operational with all components functioning within normal parameters.

Responded to service call for non-functioning electrical outlets and light fixtures in living room, kitchen, and bathroom. Upon inspection, identified tripped circuit breakers in the main electrical panel affecting multiple circuits. Reset affected breakers, restored power to the living room outlet, kitchen sink light fixture, and bathroom vanity light fixture, and verified proper operation of all components.

Responded to no cooling call on 10+ year old second floor system with frozen refrigerant line at condenser. Upon inspection, found restricted airflow at air handler due to excessive dust accumulation on blower wheel and housing of GCUH-36A-070 unit. Cleaned blower assembly, verified motor operation, and restored proper system airflow to resolve freezing condition.

Responded to cooling failure on 15-year-old Frigidaire attic unit where indoor fan operated but system failed to reduce temperature. Customer had previously made attic accessible by installing walkway boards and lighting. Upon inspection, accessed electrical panel and identified circuit breaker issue affecting compressor operation, preventing refrigeration cycle from engaging properly despite blower function.

Performed comprehensive cooling maintenance on 5-year-old Lennox system. Completed full AC tune-up including inspection of electrical components, wiring connections, and control systems within the unit compartment. Replaced 20x25x1 air filters to ensure optimal airflow and system efficiency. All electrical terminals, relays, and wire connections were inspected and found secure. Verified system operation and confirmed unit is functioning properly with no issues detected.

Completed comprehensive cooling maintenance on 15-year-old residential air conditioning system. Performed standard tune-up procedures including filter replacement, system inspection, and verification of proper operation. All components functioning within normal parameters at time of service completion.

Responded to report of water pooling around 10-year-old furnace unit located in basement. Upon arrival, inspected condensate drain system and found blockage preventing proper drainage. Cleared obstruction from drain line, verified proper flow, and confirmed no additional leaks present.

Returned to property to confirm location of refrigerant leak as previously identified during maintenance visit. Performed diagnostic testing using digital multimeter to check electrical readings and system performance. Measured amperage draw at 1.52A and voltage readings, then conducted follow-up measurements showing 5.91A draw to verify compressor and system operation. Confirmed leak location and documented findings for repair quote preparation.

Completed cooling system tune-up on 2005 AC unit, performing standard maintenance protocol including inspection of evaporator coil, refrigerant lines, electrical connections, and air filters. Noted previous gas leak issue addressed by utility company and identified unsealed opening in basement brick wall where furnace and water heater flue penetrates, recommending proper sealing to prevent air infiltration and maintain building envelope integrity. All cooling system components operating within normal parameters upon completion of service.

Replaced evaporator coil with correct Lennox model 29A19 after incorrect coil was installed in June. Retrieved warranty replacement coil and completed installation, removing and disposing of incorrect unit. Verified system operation for both heating and cooling modes upon completion.

Completed comprehensive cooling system tune-up on two U10 units located in basement and attic. Performed full system diagnostics including amperage testing with clamp meter, inspected compressor motors and cooling fins, verified electrical connections, checked refrigerant levels, and cleaned condenser coils. Both units tested within normal operating parameters and are functioning properly for the cooling season.

Responded to no cooling call on 9-year-old Rheem system. Found severely clogged air filter restricting airflow, causing system to fail to operate despite thermostat clicking normally after battery replacement. Removed and replaced dirty filter with new unit, restoring proper airflow to evaporator coil and heat exchanger. System tested and confirmed operational with adequate cooling performance restored.

Responded to service call for outdoor A/C condenser unit not turning on. Upon arrival, inspected 9-year-old air conditioning system and diagnosed electrical failure preventing compressor operation. Tested capacitor and contactor, found faulty contactor preventing power delivery to compressor and condenser fan motor. Replaced defective contactor with OEM-equivalent component, verified proper voltage and amperage readings, and restored unit to full operational status with normal cooling cycle.

Completed comprehensive preventative maintenance tune-ups on two residential cooling systems, both over 10 years old and located in the backyard. Performed thorough inspection of all components including circuit boards, electrical connections, refrigerant lines, and blower assemblies. Verified proper operation of control boards, checked wire bundles and connections for secure mounting, and inspected copper refrigerant lines for integrity. Documented equipment specifications and manufacturing dates for service records, with one unit manufactured in December 2017. All systems tested and operating within normal parameters upon completion.

Completed comprehensive cooling system tune-up on 2017 residential AC unit located at ground level. Performed standard maintenance protocol including system inspection, replaced heavily soiled 16x25x1 air filter, verified electrical connections and control board operation, and confirmed all components functioning within normal parameters. Unit operating efficiently with no issues identified.

Completed electrical panel replacement in utility/mechanical room. Installed new panel with proper wire management and routing of multiple circuits, ensuring all electrical connections meet code requirements. Work area prepared with appropriate access to existing plumbing and utility systems during installation.

Replaced failed evaporator coil in second-floor air conditioning system due to no cooling condition. Removed and disposed of defective coil, installed new evaporator coil assembly, and performed complete system evacuation and refrigerant recharge. Verified proper system operation with refrigerant pressures, subcooling, and saturation temperatures within manufacturer specifications.

Completed cooling system tune-up on a 10+ year old outdoor unit located in backyard. Inspected and documented electrical components including capacitor showing age-related wear and surface oxidation. Cleared debris accumulation around unit base and verified proper drainage from condensate lines.