Plumbing & HVAC in Florissant, MO

Completed comprehensive AC Super Tune service on Ruud residential HVAC system with age unknown to homeowner. Performed full system inspection including furnace, evaporator coil, and control board components. Verified all electrical connections, refrigerant line integrity, gas piping, and shut-off valves functioning properly. Inspected control board wiring and terminals, confirmed proper operation of all safety controls and system components. System operating within normal parameters with no deficiencies noted at time of service.

Completed comprehensive Supertune maintenance service on a 10-year-old combination AC and heat pump furnace system located at ground level in the rear of the property. Performed full system inspection with furnace cabinet opened to access and evaluate internal components including blower motor assembly, electrical connections, and mechanical operations. Conducted standard tune-up procedures on both heating and cooling systems to ensure optimal performance and efficiency for the upcoming season.

Responded to residential service call to repair or replace two receptacles and switches. Upon arrival, performed visual inspection of electrical system including exterior meter base, service entrance equipment, and associated wiring connections. Documented existing conditions with photographs showing digital utility meter, exterior junction boxes, and service conduit installation. Accessed interior locations to evaluate and service the affected receptacles and switches as requested. Completed necessary repairs or replacements to restore proper functionality to the electrical devices. Verified all connections were secure and tested circuits to ensure safe operation. All work performed in accordance with National Electrical Code standards.

Responded to no cooling complaint on Lennox system following power outage from transformer failure. Upon arrival, found unit running but house temperature at 85°F. Diagnosed issue as thermostat programming lost during power interruption on recently installed digital thermostat. Reprogrammed thermostat to proper cooling setpoints and verified system operation. Used clamp meter to verify amperage draw on compressor and confirmed readings within manufacturer specifications. Connected manifold gauges to measure refrigerant pressures and temperatures, confirming system charging and performance parameters were correct at 142.3 PSI high side and 117 PSI low side with superheat at acceptable levels. Instructed occupant on proper thermostat operation and programming procedures to prevent future issues. System cooling properly upon departure with all components operating as designed.

# HVAC Tune-Up Completed Performed comprehensive preventative maintenance tune-up on a single outdoor air conditioning condenser unit located in backyard. Conducted standard inspection protocol including visual assessment of unit exterior, electrical disconnect box, conduit connections, and mounting hardware. Verified proper clearance around unit despite vegetation growth near base and wall-mounted components. Inspected indoor air handler system with focus on filter specifications and operational safety labels. All routine maintenance tasks completed per manufacturer guidelines for optimal system performance and seasonal readiness.

Completed electrical estimate for sub panel installation at residential property. Evaluated existing main electrical panel, which contains two columns of circuit breakers serving various household circuits including HVAC, water heater, kitchen appliances, bedrooms, and living areas. Observed dense wiring configuration with multiple wire runs and connections throughout the existing panel enclosure. Assessed current electrical load distribution and available capacity to determine specifications and requirements for proposed sub panel installation. Documented existing panel condition and circuit layout to develop accurate scope of work and material requirements for the sub panel project.

Responded to no cooling complaint on 8-year-old Lennox central air conditioning system with attic-mounted air handler. Upon arrival, discovered condensate drain line completely blocked, causing secondary drain pan to overflow and trip safety float switch, which shut down the system. Cleared obstruction from primary drain line, flushed condensate system with approved cleaning solution, and verified proper drainage flow. Tested float switch operation and confirmed system restored to normal cooling operation with proper airflow and temperature differential across evaporator coil.

Responded to clogged bathroom sink caused by deteriorated P-trap assembly with visible corrosion at metal coupling and compromised pipe integrity. Removed failed trap section showing extensive mineral buildup and coating degradation, installed new P-trap assembly with proper sealing, and verified drainage flow restoration. Cleared standing water and confirmed all connections leak-free upon completion.

Responded to water leak complaint on residential furnace system located in basement. Upon arrival, performed visual inspection of HVAC unit less than 10 years old. Identified water leakage originating from furnace area. Inspected Aprilaire humidifier component and associated copper piping connections for potential leak sources. Examined air handler unit, condensate drainage system, and surrounding ductwork for moisture accumulation. Documented system conditions with photographic evidence showing air filter assembly, humidifier installation, and copper refrigerant lines. Unable to complete full diagnostic assessment and repair at time of visit. System requires follow-up service to isolate leak source and implement necessary repairs to resolve water discharge issue.

Responded to loss of power affecting main level circuits. Upon inspection, found electrical panel with debris accumulation at bottom and signs of oxidation on bus bar connections. Cleared contamination from panel interior, inspected all breaker connections, and verified proper circuit operation to restore full power to affected areas.

Completed cooling system tune-up on single outdoor condensing unit. Performed comprehensive maintenance inspection, checked refrigerant levels, cleaned condenser coils, verified electrical connections, and tested system operation. Replaced 14x25x1 air filter to ensure proper airflow and system efficiency.

Completed installation of electric vehicle charging station including electrical panel modifications and circuit breaker installation. Mounted charging equipment on interior wall, ran necessary wiring from main service panel, and installed dedicated circuit protection to support the EV charger load requirements per manufacturer specifications and local electrical code.

Returned to complete AC repair on 12-year-old Lennox unit that was previously started but left unfinished. Accessed outdoor condensing unit, completed electrical connections and wiring terminations, secured all internal components, and restored unit to operational status. System tested and confirmed cooling restored after being inoperative for over a week.

Completed cooling tune-up on 10-year-old Trane XV80 system. Replaced 18x24x1 air filter and inspected evaporator coil, which showed significant dust and debris accumulation between fins requiring attention. Performed standard maintenance procedures including system inspection, verified refrigerant lines, and assessed overall unit operation to ensure proper cooling performance for the upcoming season.

Responded to commercial property for sewer lateral line obstruction caused by grout material that had accidentally entered the line during construction or renovation work. Accessed the sewer cleanout located in the interior floor opening and performed mechanical cleaning to remove hardened grout blockage from the lateral line. Restored proper flow and drainage to the sewer system, with line now clear and operational.

Completed comprehensive cooling system tune-up on 2-year-old Lennox air conditioning unit. Performed full preventive maintenance inspection including condenser coil cleaning, electrical connections check, refrigerant level verification, and system performance testing. Unit operational and running efficiently with no issues identified; condenser coils found in clean condition and all components functioning within manufacturer specifications.

Completed comprehensive tune-up service on two residential air conditioning systems. Upon arrival, found outdoor condensing unit with significant dirt accumulation and debris around equipment perimeter. Performed thorough inspection of both units, including visual assessment of condenser coils which revealed heavy buildup of dust, lint, and particulate matter restricting airflow through fin structure. Cleaned condenser coils to restore proper heat transfer efficiency and checked all electrical connections. Verified refrigerant lines, tested system operation, and cleared surrounding area of leaves and organic debris to ensure adequate ventilation clearance around equipment.

Completed installation of customer-provided thermostat in 4-year-old residential property. Verified whole house electrical system functionality, including main service panel with properly labeled circuit breakers controlling HVAC, dryer, hot tub, and other household circuits. Confirmed exterior meter installation and service entrance conduit configuration met code requirements prior to proceeding with thermostat installation as requested.

Completed comprehensive O10 cooling tune-up on backyard AC unit. Performed full system inspection including electrical testing with digital multimeter, verified capacitor operation and readings, checked all electrical connections and components. Unit found to be operating within normal parameters with all measurements acceptable.

Installed electric vehicle charging station in residential garage. Assessed existing electrical service entrance and main panel capacity to ensure adequate power supply for Level 2 EV charger installation. Ran dedicated 240-volt circuit from main electrical panel to garage location, installed appropriate conduit and wiring per NEC requirements, and mounted charging port on garage wall. Verified proper grounding, tested circuit functionality, and confirmed charging station operational status upon completion.